Operation instrction Of Roller press(4)

第三章 技术性能及参数
Chapter 3 Technical Performance and Parameters
 
详见订货合同要求及设备安装总图及装配图中的技术要求和参数。
For details, see the order contract requirements and the technical requirements and parameters in the equipment installation general drawings and assembly drawings. 
 
第四章 基础要求及供货范围
Chapter 4 Foundation Requirements and Scope of Supply
一.对基础的要求
1. Requirements for the foundation
辊压机可以安装在地平面上,也可以安装在楼板上,可以采用钢筋混凝土基础,也可采用钢结构基础。
The roller press can be installed on the ground plane or on the floor. It can be the reinforced concrete foundation or the steel structure foundation.
由于挤压粉碎力全部在封闭的机架被平衡,故对基础主要考虑其机身重量和水平,垂直动载荷系数。
Since the crushing force is fully balanced in the closed frame, the weight of the body and the horizontal and vertical dynamic load coefficients are mainly considered for the foundation.
1.主机重量按100吨考虑。若将主机基础分为两部分,其各需承受的重量可以按设备长度比例进行估算。
1. The weight of the main machine is considered as 100 tons. If the base of main machine is divided into two parts, the weight that each needs to bear can be estimated in proportion to the length of the equipment.
2.基础的垂直动载荷系数,可以按1考虑。
2. The vertical dynamic load factor of the foundation can be considered as 1.
3.基础的水平动载荷系数,可以按0.8考虑。
3. The horizontal dynamic load factor of the foundation can be considered as 0.8.
二.辊压机配套供应范围:
2. Supply range of roller press:
1．由生产厂家供货的设备
1. Equipment supplied by the manufacturer
⑴主机本体(包括机架、轴承等七大部分)一套
⑴One set of main machine body (including seven parts such as frame and bearing)
⑵带缩套联轴器的行星减速器两套
⑵Two sets of planetary reducer with shrink sleeve coupling
⑶万向节传动轴两套
⑶Two sets of universal joint drive shafts
⑷高压三相异步电动机(用户可自购或委托制造商配套)
⑷High-voltage three-phase asynchronous motor (users can purchase by themselves or entrust the manufacturer to support them)
⑸主机微机控制柜
⑸Main machine computer control cabinet
⑹主电机控制柜3
⑹Main motor control cabinet 3
⑺附件: Ⅰ液压蓄能器充气工具一套
⑺Accessories: ⅠA set of charging tools for hydraulic accumulator
       Ⅱ耐磨焊条10kg
Ⅱ Wear-resistant electrode 10kg
2．用户自备设备
2. User-supplied equipment
⑴集中润滑充填泵(手动或自动)
⑴ Centralized lubrication and filling pump (manual or automatic)
⑵扭力矩搬手(250～750Nm)及六角套筒M30、M20螺栓配套)
⑵ Torque handle (250～750Nm) and hexagon socket M30, M20 bolts matching)
⑶氮气瓶两只
⑶Two nitrogen bottles
⑷除铁器(皮带自卸式)
⑷Iron remover (belt self-unloading type)
⑸称重仓及传感器
⑸ Weighing bin and sensor